Low-speed trucks are used as intermediate products between tractors and automobiles and are mainly developed for the rural market. With the changes in the country's rural policies, the use of agricultural vehicles has generally increased. Low-speed trucks are a type of agricultural vehicle, and they are favored by many farmers. However, when driving this kind of vehicle, there are some hazards caused by wrong driving. Always keep this in mind and avoid this situation.
First, the hazard of speeding of low-speed trucks
The characteristics of rural transport in general are the small volume of transport, the relatively short distance, the lack of concentration of goods, and the relatively poor road conditions relative to the city. Low-speed trucks do not require high speeds when driving on such roads. Set the speed below 70 kilometers per hour. Once the engine is overdriven for a long time, the wear of the engine, chassis, tires, and brakes will increase. Once the limits of the vehicle itself are exceeded, the safety technology status will drop sharply and the safety risks will increase. In addition, speeding will also cause greater vehicle vibration and engine noise, which can easily lead to driver fatigue. This can easily lead to traffic accidents. Therefore, be sure to refuse speeding.
Second, the illegal loading of low-speed trucks
According to the principle of traffic regulations, trucks are prohibited from carrying people. There are few traffic policemen in rural areas to inspect. Therefore, many farmers' friends will have a chance of being lucky. However, Xiao Bian wants to tell everyone that, like low-speed trucks, when the performance, structure, and safety technology of the car were originally designed for short-distance transportation of agricultural goods, they do not have the conditions for carrying passengers. And it is very limited to carry overcapacity. In addition, the transportation environment is shuttled to the fields and the vehicles wear out. Unpredictable consequences occur in case of accidents. Therefore, for personal safety, refuse to carry people.
Third, the risk of overloading cargo on low-speed trucks
As mentioned above, low-speed trucks are low-speed vehicles that specialize in rural road transportation. Their technical requirements in terms of structure and safety are proposed for short-haul transportation. Once the cargo is overloaded, the engine will run under overload conditions for a long time, which will result in fatigue and wear of the machine parts. The safety technology situation will be severely reduced, and it is easy to cause direction deviation, brake failure, car deformation, axle cutoff. , Tire cracks and other phenomena, the probability of traffic accidents caused by long-term overloading is high. In addition, low-speed trucks often travel on rural roads or fields, yards, etc., and road conditions are generally poor. If they cannot be maintained in time, safety risks will be greater. So be sure to remember not to overload.
Metal Body Square Water Cooling Tower
This series of products run stable, low noise, energy-saving, in office buildings, shopping malls, hotels, residential areas and other central air-conditioning supporting the use of better results.
The company's standard cooling tower according to the international design conditions design, can also provide customers with non-standard operating conditions or specific sizes under the special, special design.
The circulating water pump suction port shall be located below the water level of the cooling tower catchment basin, and the cooling tower outlet pipe shall not be allowed to be higher than the maximum water level of the catchment basin.
Pipe mounts should be pipe racks and cooling towers should not be allowed to directly bear the weight of the pipes.
The rehydration pipe of the cooling tower should be provided with a support stand to avoid vibration of the pipe when the float valve is rehydrated.
Rehydration pressure should be below 5m water pressure, national standard
The flannage pressure is 1.0Mpa.
When two or more units are assembled, our company will provide a connecting balance tube to balance the chassis water level. The tower top inlet should be set with a conditioning valve in order to enter each
.The water level of the tower is uniform.
The noise is measured at dm1.13VL-W at the equivalent diameter of the cooling tower (Dm1.13VL*W), 1.5 meters above the ground height, wherein L and W are the shape rulers of the tower
inch long and wide).
The use of cellular continuous blister series of diversion,heat dissipation, water collection three-in-one native filler, the whole suspension, gravity cloth water, low drop of water, with cold effect
High, low energy consumption, less drift water, less noise and so on, floating water rate is less than 0.001%.
When connecting different types of towers, the bottom basin water level height of different types of towers must be taken into account, and the base height must be adjusted to maintain the water level balance of the towers.
Metal Body Square Water Cooling Tower,Tower Water Cooler,Water Cooled Cooling Tower,Tower Cooling System
Wuxi Ark Fluid Science Technology Co., Ltd. , https://www.fangzhouarkfluid.com