Sprinkler fault causes and remedies

Sprinkler fault causes and remedies

After a sprinkler has been used for a period of time, there are usually minor problems that prevent it from working properly, causing inconvenience to users. Sprinkler fault is usually related to sprinkler pumps, three-way ball valves, strainers, etc. Here we come to understand one by one, how to troubleshoot.
Sprinklers for watering sprinklers Troubleshooting method I. Sprinklers for watering pumps cannot be self-priming Causes:
1. There is not enough liquid or liquid in the sprinkling sprinkling system for the sprinkler. 2. Sprinklers for the sprinkling pump in the sprinkler system. 3. The speed of the sprinkling system for the sprinkling system is too low. 4. The suction system for the water pump is too high or the suction pipe is too high. The road is blocked 5, Sprinklers dedicated sprinkler pump mechanical seal contamination too much Sprinklers dedicated sprinkler pump can not self-priming Troubleshooting:
1. Add enough fluid 2. Check and eliminate leaks 3. Adjust the rotational speed 4. Low suction or shorten the suction line 5. Repair or replace 2. Inadequate pressure caused by the sprinkler
1. Impediment to the flow path of the impeller or suction pipe 2. Abrasive wear of the impeller or impeller seal ring 3. Insufficient power and low rotation speed 4. Inadequate pressure at the inlet or outlet valve
1. Elimination of blockages 2, replacement of the ring 3, addition of full horsepower to adjust the speed 4, open the inlet or outlet valve
Third, the sprinkler truck dedicated sprinkler shaft power consumption is too much cause:
1, the flow is too large 2, the speed is too high 3, the pump shaft is twisted or the impeller bumps, the inner flow channel is blocked or stuck sprinkler special sprinkler shaft power consumption is too high Troubleshooting method:
1, reduce the flow 2, reduce properly 3, correct or replace 4, eliminate plugging 4, sprinkler car sprinkler noise greater vibration causes:
1, unstable foot 2, cavitation 3, bearing wear is serious 4, sprinkler car sprinkler pump is blocked or stuck in the flow channel 5, sprinkler sprinkled water pump or imported pipe debris, sprinkler car sprinkler and The main shaft of the power machine is different from the main shaft and sprinkler.
1, reinforcement
2, adjust the operating conditions
3, replace the new bearing
4, correction or replacement
5, remove debris
6, adjust the coaxiality
V. Ball valve failure
1, cylinder failure
2, valve core damage
First check the electricity, gas path is loose, you can replace the ball valve.
Sixth, the water tank does not produce water
The jug is dirty and the filter is clogged. Timely cleaning of water tanks, strainers, removal of debris.

Precision CNC Turning

CNC Turning is a manufacturing process in which bars of material are held in a chuck and rotated while a tool is fed to the piece to remove material to create the desired shape. A turret (shown center), with tooling attached is programmed to move to the bar of raw material and remove material to create the programmed result. This is also called [subtraction machining" since it involves material removal. If the center has both tuning and milling capabilities, the rotation can be stopped to allow for milling out of other shapes.

  • The starting material, though usual round, can be other shapes such as squares or hexagons.
  • Depending on the bar feeder, the bar length can vary. This affects how much handling is required for volume jobs.
  • CNC lathes or turning centers have tooling mounted on a turret which is computer-controlled. The more tools that that the turret can hold, the more options are available for complexities on the part.
  • CNC`s with [live" tooling options, can stop the bar rotation and add additional features such as drilled holes, slots and milled surfaces.
  • Some CNC turning centers have one spindle, allowing work to be done all from one side, while other turning centers, such as the one shown above, have two spindles, a main and sub-spindle. A part can be partially machined on the main spindle, moved to the sub-spindle and have additional work done to the other side this configuration.
  • There are many different kinds of CNC turning centers with various types of tooling options, spindle options, outer diameter limitations as well as power and speed capabilities that affect the types of parts that can be economically made on it.
Stainless Steel Thermowell HousingStainless Steel Thermowell FittingCnc Turning Aluminum Shaft

Precision Cnc Turning,Performance Shaft,Stainless Steel Shaft,Aluminum Auto Parts

Yihua Precision Machining Co, Ltd. , https://www.yhmachining.com

This entry was posted in on